Evaluating Loose Hinges Before They Fail

Evaluating Loose Hinges Before They Fail

Historical Development and Evolution of Auto Reverse Technology

Garage doors are a crucial component of home security and functionality, often going unnoticed in their daily operation until something goes awry. One of the most common issues homeowners face with garage doors is loose hinges, a seemingly minor problem that can lead to significant inconvenience if not addressed promptly. Evaluating and understanding the common causes of loose hinges before they fail can save time, money, and potential safety hazards.


Loose hinges in garage doors are typically the result of wear and tear over time. Garage door keypads provide an additional layer of convenience for access commercial garage door repair truck. The constant opening and closing of the door put stress on the hinges, gradually loosening them. This natural degradation is exacerbated by factors such as inadequate maintenance, poor installation quality, or environmental conditions like humidity and temperature fluctuations. Metal fatigue is another contributing factor; as metal components expand and contract with temperature changes, they can weaken over time, leading to loosened screws or even cracked hinge plates.


Another prevalent cause of loose hinges is improper use or accidental damage. Garage doors occasionally bear more weight than they should when misused for storage purposes or subjected to impacts from vehicles or other equipment. Such incidents can shift the door's alignment, placing undue pressure on specific hinges and causing them to loosen prematurely.


Additionally, poor initial installation can set a garage door up for failure from the start. If the door was not properly aligned during installation or if subpar materials were used for hinge components, it increases the likelihood of problems developing sooner rather than later. Ensuring that all parts are correctly fitted and secured during installation is vital for long-term reliability.


To effectively evaluate loose hinges before they become problematic, regular inspection is essential. Homeowners should periodically check their garage door's operation for unusual noises or movements that could indicate an issue with the hinges. Tightening any visibly loose screws can often prevent further deterioration but must be done carefully to avoid stripping threads or damaging components.


In conclusion, while loose hinges may seem like a minor inconvenience in the grand scheme of home maintenance tasks, addressing them proactively is essential to prevent more severe problems down the line. By understanding common causes such as wear and tear, improper use, environmental factors, and poor installation practices-and by conducting regular inspections-homeowners can ensure their garage doors remain functional and reliable for years to come.

In our daily lives, we often take for granted the simple mechanisms that allow us to move effortlessly through spaces-doors being a prime example. Yet, it is crucial to recognize the subtle signs that indicate when these mechanisms, particularly hinges, are on the verge of failing. Identifying the signs of deteriorating hinges before failure occurs is not merely a matter of convenience but also one of safety and cost-effectiveness.


Hinges serve as pivotal components in any door system, providing both support and movement. Over time, however, even the most robust hinges can begin to show signs of wear and tear. One of the earliest indicators of deterioration is a noticeable squeak or creak when the door is opened or closed. This often results from insufficient lubrication or accumulated dirt and debris between moving parts. Ignoring this auditory warning can lead to further degradation and ultimately necessitate more extensive repairs.


Another telltale sign is increased resistance or stiffness in door movement. If you find yourself exerting more effort to open or close a door than previously required, it may indicate that the hinge pins are misaligned or worn out. In such cases, immediate attention can prevent further damage not only to the hinges themselves but also to adjoining structures like door frames.


A visual inspection can also reveal much about a hinge's condition. Rust and corrosion are common culprits in metal hinges exposed to moisture over time. The presence of rust not only weakens the structural integrity but also hampers smooth operation. Regularly checking for discoloration or flaking metal can help catch these issues early on.


Moreover, look out for loose screws or bolts in hinge assemblies-this could be an indication that they have been subjected to unusual stress or vibration over time. Tightening these components might suffice temporarily; however, repeated loosening suggests an underlying problem with either alignment or material fatigue.


Taking proactive measures by regularly evaluating loose hinges before they fail can save homeowners significant distress later on. Simple maintenance tasks such as cleaning away dirt buildup and applying lubricant every few months extend hinge longevity exponentially while ensuring their optimal performance.


In conclusion, understanding how to identify deteriorating hinges before they reach failure is essential knowledge for anyone responsible for property upkeep-from homeowners maintaining their abodes' functionality to facilities managers overseeing larger infrastructures' reliability standards alike! By paying heed now unto small yet telling signals given off by aging apparatuses around us-and acting accordingly-we safeguard both convenience within our environments alongside safeguarding against unforeseen liabilities posed otherwise downstream therein too!

How To Safely Inspect Cables And Springs For Wear And Tear

In the fast-paced world we live in, it's easy to overlook the importance of maintenance routines.. Yet, when it comes to safety, particularly concerning cables and springs, prioritizing these routines is not just advisable—it's essential.

How To Safely Inspect Cables And Springs For Wear And Tear

Posted by on 2025-01-02

The Connection Between Regular Maintenance And Garage Door Efficiency

When it comes to ensuring the efficient operation of your garage door, regular maintenance is key.. The debate often arises between opting for professional maintenance services or undertaking a do-it-yourself (DIY) approach.

The Connection Between Regular Maintenance And Garage Door Efficiency

Posted by on 2025-01-02

Ensuring Child And Pet Safety Around Automated Garage Doors

In recent years, the integration of automated garage door systems into homes has become increasingly common, offering unparalleled convenience and efficiency.. However, with this advancement comes an essential responsibility: ensuring the safety of children and pets around these powerful devices.

Ensuring Child And Pet Safety Around Automated Garage Doors

Posted by on 2025-01-02

Safety Benefits of Installing Auto Reverse Mechanisms

Evaluating the integrity of hinges, particularly before they fail, is a crucial task that often goes unnoticed until it's too late. Hinges are fundamental components in many structures, from doors and gates to cabinets and machinery. Ensuring their proper function not only preserves the aesthetic and operational quality of these systems but also prevents potential safety hazards. Understanding the tools and techniques for inspecting hinge integrity can provide significant benefits in maintenance routines.


One of the primary indicators of a loose hinge is its movement or sagging when weight or force is applied. Visual inspection is often the first step in assessing hinge health. Look for signs such as misalignment, unusual gaps between moving parts, or rust and corrosion that may have compromised the hinge material over time. These visible cues can offer immediate insight into whether further investigation is warranted.


For a more thorough examination, employing specific tools can greatly enhance the accuracy of an assessment. A spirit level or laser level can be used to check alignment between hinged components; any deviation might suggest wear or loosening in the hinge mechanism itself. Additionally, feeler gauges are useful for measuring gaps around hinges to determine if there's excessive play indicating wear.


Auditory cues should not be overlooked during inspections: squeaks, creaks, or grinding noises often accompany loose hinges and signal that lubrication might be needed or that mechanical failure could be imminent. In cases where lubrication does not resolve these sounds, disassembly might be required to inspect internal components for damage.


For more sophisticated analysis, especially in industrial settings where hinges bear significant loads, non-destructive testing (NDT) methods like ultrasonic testing can detect internal flaws without dismantling structures. This technique utilizes high-frequency sound waves to identify cracks or weaknesses within metal hinges which are invisible to the naked eye.


When dealing with particularly heavy-duty applications such as large doors or machinery panels, torque wrenches may come into play during both inspection and maintenance phases. Measuring the torque required to move a hinge can help ascertain whether it has loosened over time; adjustments can then be made according to manufacturer specifications to restore optimal function.


Regular maintenance schedules incorporating these inspection techniques ensure longer life spans for hinges by catching issues early before they escalate into failures requiring costly repairs or replacements. Educating oneself on these practices empowers individuals and businesses alike to maintain safer environments while preserving functionality across various applications.


In conclusion, evaluating loose hinges before they fail relies on both keen observation and adept use of appropriate tools and techniques. By combining visual assessments with advanced diagnostic tools where necessary, one can effectively monitor and maintain hinge integrity-ultimately ensuring safety and efficiency within any structural system relying on hinged movements.

Safety Benefits of Installing Auto Reverse Mechanisms

Common Issues and Troubleshooting Tips for Auto Reverse Systems

Evaluating loose hinges before they fail is a crucial task that often goes overlooked in household maintenance. Hinges, though small and seemingly insignificant, play a vital role in the functionality and security of doors, cabinets, and other movable fixtures. When they become loose, the consequences can range from annoying squeaks to compromised safety and security. Therefore, understanding how to evaluate these components before they fail is essential for any diligent homeowner or handyman.


The initial step in evaluating loose hinges involves a careful inspection. Begin by observing the door or cabinet's movement. Does it sag or stick when opened or closed? These are telltale signs that the hinges may be loose. Next, listen for any unusual noises such as grinding or squeaking; these auditory cues can indicate that the hinge is not functioning optimally.


Once visual and auditory checks are complete, proceed with a tactile examination. Gently wiggle the door or fixture while watching the hinge closely. If there is noticeable movement between the hinge leaves and their mounting surfaces, it's a clear indication of looseness. Additionally, check for any visible gaps between the hinge leaves themselves or between the leaves and screws; this often signals wear or damage.


After identifying potential issues through inspection, it's important to determine their cause before proceeding with repairs. Loose hinges can result from various factors including wear over time, improper installation, or even environmental conditions such as humidity which can warp wood around screw holes.


To address these issues effectively, you need to remove each screw carefully to assess its condition as well as that of its hole in the frame or door edge. Stripped screws and enlarged holes are common culprits behind insufficiently secured hinges.


Armed with this knowledge from your evaluation process, you can now move onto tightening and securing those troublesome loose hinges using appropriate methods like replacing worn-out screws with longer ones for better grip or filling enlarged holes with wooden dowels before re-screwing them securely back inplace.


In conclusion,evaluating loose hinges should never be underestimated since early detection allows homeownersand handymen alike an opportunityto act preemptively preventing further damageor inconvenience.Taking timefor regular inspectionsensures smooth operationof doors,cabinets,and otherfixtureswhile preservingtheir longevityand maintainingoverall homestead integrity.So,next timeyou hearthat familiar creakor noticea slightsag,it mightjust bethe perfecttimefora thoroughhingeevaluation!

The Role of Regulations and Standards in Ensuring Safety

Preventative Maintenance Tips for Long-Lasting Hinge Performance: Evaluating Loose Hinges Before They Fail


In the realm of household upkeep, hinges often reside in the shadows, quietly performing their crucial role of supporting doors and cabinets. These small yet pivotal components can easily be overlooked until they become a source of frustration due to squeaking or loosening. However, by adopting a proactive approach to evaluating and maintaining hinges, homeowners can ensure long-lasting performance and avoid inconvenient malfunctions.


The importance of preventative maintenance cannot be overstated when it comes to hinges. Just like any other mechanical part that experiences regular use, wear and tear is inevitable. Over time, this can lead to hinges becoming loose-a precursor to failure if left unaddressed. Thus, periodic evaluation is key to catching potential issues early.


Begin by visually inspecting your hinges on a regular basis. Look for signs of wear such as rust, discoloration, or deformation. Rust is particularly concerning as it not only weakens the metal but also indicates exposure to moisture-an environment where deterioration can accelerate. Discoloration may signal that the hinge material is degrading or reacting with environmental factors.


Next, test the movement of your doors or lids attached to these hinges. Do they open smoothly without resistance? Any signs of sticking or jerking could suggest that the hinge is misaligned or beginning to loosen. Pay attention to any unusual noises; a squeak might seem trivial but often serves as an early warning sign that lubrication is needed.


To further assess hinge stability, gently lift the door while observing for any movement at the hinge joint. A secure hinge should remain firmly in place without excessive play in its components. If you notice significant movement or if screws are visibly loose, immediate action should be taken.


Fortunately, addressing loose hinges usually involves straightforward solutions. Start by tightening any screws that have come undone over time using an appropriately sized screwdriver-be cautious not to overtighten as this might strip the screw holes or damage softer materials like wood.


For persistent looseness where screws refuse to hold firm despite being tightened, filling stripped holes with wood filler and re-drilling them once dry can provide a more robust grip for screws.


Lubrication forms another essential aspect of preventative care for hinges. Regular application of lubricant helps reduce friction between moving parts and prevents squeaks while ensuring smooth operation over extended periods. Opt for lubricants specifically designed for metal components; avoid household oils which may attract dust and grime buildup leading potentially damaging residue over time.


Finally-and importantly-consider environmental factors influencing your hinge's longevity: humidity levels within homes significantly impact metal hardware prone towards corrosion under damp conditions hence controlling indoor climate via dehumidifiers where necessary proves beneficial alongside routine cleaning practices keeping dirt accumulation at bay thus extending lifespan considerably longer than neglected counterparts subjected purely external elements alone would permit otherwise!


In summary then: vigilant evaluation coupled consistent maintenance measures constitute best strategy preserving optimal functionality across various settings whether residential commercial alike! By investing little effort into regularly assessing condition making minor adjustments along way homeowners stand reap rewards reliable dependable performance from their humble yet indispensable partners-the trusty hinge!

Selecting the Right Garage Door System with Effective Auto Reverse Features

When it comes to the smooth operation of doors, cabinets, or any fixture that relies on hinges, it's easy to overlook these small yet crucial components until they begin to fail. Evaluating loose hinges before they become a significant problem is an essential maintenance task that can save time, money, and frustration. However, there comes a point when professional assessment or even replacement becomes necessary.


Initially, a minor adjustment might suffice for slightly loose hinges. Tightening screws or applying lubrication can often restore functionality and prevent further deterioration. Regularly inspecting hinges for signs of wear such as squeaking, sagging, or misalignment is a proactive step homeowners can take to extend their lifespan.


However, not all hinge issues can be resolved with simple fixes. Over time, hinges may suffer from metal fatigue, corrosion, or damage that is beyond the scope of DIY repairs. When adjustments no longer yield results and the door or cabinet continues to malfunction perhaps refusing to close properly or hanging at an odd angle it's time to consider professional assessment.


A professional has the expertise to diagnose underlying problems that aren't immediately obvious. They can determine whether the issue lies in the hinge itself or if there are structural concerns with the door frame or surrounding woodwork. Ignoring these deeper issues could lead to more extensive damage over time.


Moreover, replacing old hinges with new ones isn't always straightforward. There are numerous types of hinges designed for specific purposes and materials; selecting the right one requires understanding both aesthetics and function. A professional can recommend high-quality replacements suited for your particular needs and ensure they're installed correctly for optimal performance.


In some cases, upgrading rather than simply replacing may be advisable. Newer models often come with improved designs and features that enhance durability and ease of use such as soft-close mechanisms that reduce impact stress on both the hinge and door frame.


Ultimately, while routine checks and maintenance are invaluable in prolonging hinge life, recognizing when an issue exceeds basic repair capabilities is crucial. Seeking professional help ensures safety and efficiency while minimizing potential disruption caused by failing fixtures.


In conclusion, evaluating loose hinges before they fail involves both preventative measures taken by homeowners themselves and knowing when it's appropriate to call in professionals for assessment or replacement. This balanced approach not only maintains functional integrity but also enhances overall home safety and aesthetics in the long run.

A residential garage door opener. The motor is in the box on the upper-right.

A garage door opener is a motorized device that opens and closes a garage door controlled by switches on the garage wall. Most also include a handheld radio remote control carried by the owner, which can be used to open and close the door from a short distance.

The electric opener

[edit]

The electric overhead garage door opener was invented by C.G. Johnson in 1926 in Hartford City, Indiana.[1] Electric Garage Door openers did not become popular until Era Meter Company of Chicago offered one after World War II where the overhead garage door could be opened via a key pad located on a post at the end of the driveway or a switch inside the garage.[2]

As in an elevator, the electric motor does not provide most of the power to move a heavy garage door. Instead, most of door's weight is offset by the counterbalance springs attached to the door. (Even manually operated garage doors have counterbalances; otherwise, they would be too heavy for a person to open or close them.) In a typical design, torsion springs apply torque to a shaft, and that shaft applies a force to the garage door via steel counterbalance cables. The electric opener provides only a small amount of force to control how far the door opens and closes. In most cases, the garage door opener also holds the door closed in place of a lock.

The typical electric garage door opener consists of a power unit that contains the electric motor. The power unit attaches to a track. A trolley connected to an arm that attaches to the top of the garage door slides back and forth on the track, thus opening and closing the garage door. The trolley is pulled along the track by a chain, belt, or screw that turns when the motor is operated. A quick-release mechanism is attached to the trolley to allow the garage door to be disconnected from the opener for manual operation during a power failure or in case of emergency. Limit switches on the power unit control the distance the garage door opens and closes once the motor receives a signal from the remote control or wall push button to operate the door.[3]

The entire assembly hangs above the garage door. The power unit hangs from the ceiling and is located towards the rear of the garage. The end of the track on the opposite end of the power unit attaches to a header bracket that is attached to the header wall above the garage door. The powerhead is usually supported by punched angle iron.

Recently another type of opener, known as the jackshaft opener, has become more popular.[when?] This style of opener was used frequently on commercial doors but in recent years has been adapted for residential use. This style of opener consists of a motor that attaches to the side of the torsion rod and moves the door up and down by simply spinning the rod. These openers need a few extra components to function safely for residential use. These include a cable tension monitor, to detect when a cable is broken, and a separate locking mechanism to lock the door when it is fully closed. These have the advantage that they free up ceiling space that an ordinary opener and rail would occupy. These also have the disadvantage that the door must have a torsion rod to attach the motor to.

Types

[edit]

There are six types of garage door openers:

  1. Chain drive openers. These have a chain (similar to a bicycle's) that connects the trolley to the motor.
  2. Belt drive openers use a rubber belt in place of a chain.
  3. Screw drive openers have a long screw inside the track. The trolley connects to this screw.
  4. Direct drive openers have the motor installed inside the trolley and use a gear wheel to guide the trolley along a fixed chain.
  5. Jackshaft openers mount on the wall at either end of the torsion bar.
  6. Roller openers automate roller doors, which roll upward and coil around a drum above the garage entrance, maximizing space.

These openers typically feature two tines that slide into a drum wheel within the roller door mechanism, engaging to smoothly lift or lower the door.

Remote control

[edit]

The first wireless garage door openers were invented and developed by two US inventors at the same time, one in Illinois and the other in Washington state, around 1930. They were unknown to each other.[4]

The first garage door opener remote controls were simple and consisted of a simple transmitter (the remote) and receiver which controlled the opener mechanism. The transmitter would transmit on a designated frequency; the receiver would listen for the radio signal, then open or close the garage, depending on the door position. The basic concept of this can be traced back to World War II. This type of system was used to detonate remote bombs. While novel at the time, the technology ran its course when garage door openers became popular. While the garage door remote control transmitter is low power and has limited range, its signal can be received by other, nearby, garage door openers. When two neighbors had garage door openers, then opening one garage door might open the neighbor's garage door as well.

The second stage of the wireless garage door opener system solved the opening-the-neighbor's-garage-door problem. The remote controls on these systems transmitted a digital code, and the receiver in the garage responded only to that code. The codes were typically set by eight to twelve DIP switches on the receiver and transmitter, so they allowed for 28 = 256 to 212 = 4,096 different codes. As long as neighbors used different codes, they would not open each other's garage doors. The intent of these systems was to avoid interference with nearby garage doors; the systems were not designed with security in mind. Intruders were able to defeat the security of these systems and gain entry to the garage and the house. The number of codes was small enough that even an unsophisticated intruder with a compatible remote control transmitter could just start transmitting all possible codes until he found one that opened the door. More sophisticated intruders could acquire a black box master key that automatically transmitted every possible code in a short time. An even more sophisticated method is known as a replay attack. The attacker would use a code grabber, which has a receiver that captures the remote's digital code and can retransmit that digital code at a later time. The attacker with a code grabber would wait nearby for the homeowner to use his remote, capture the code, and then replay the code to open the door when the homeowner was gone. Multicode openers became unpopular in areas where security was important, but due to their ease of programming, such openers are often used to operate such things as the gates in gated apartment complexes.

An intermediate stage of the garage door opener market eliminated the DIP switches and used remotes preprogrammed to one out of roughly 3.5 billion unique codes. The receiver would maintain a security list of remotes to which it would respond; the user could easily add the unique remote's code to the list by pressing a button on the garage door opener while activating the remote control. A large number of codes made the brute force try-all-possible-digital-codes attacks infeasible, but the systems were still vulnerable to code grabbers. For user convenience, these systems were also backward compatible with the older DIP switch remote codes, but adding an old technology remote to the security list made the garage door opener vulnerable to a brute force attack to find the DIP switch code. The larger code space approach was an improvement over the fixed DIP switch codes but was still vulnerable to the replay attack.

The third stage of garage door opener technology uses a frequency spectrum range between 300-400 MHz and rolling code (code hopping) technology to defeat code grabbers. In addition to transmitting a unique identifier for the remote control, a sequence number and an encrypted message are also sent. Although an intruder could still capture the code used to open a garage door, the sequence number immediately expires, so retransmitting the code later would not open the garage door. The encryption makes it extremely difficult for an intruder to forge a message with the next sequence number that would open the door. Some rolling code systems are more involved than others. Because there is a high probability that someone will push the remote's button while not in range and thus advance the sequence number, the receiver does not insist the sequence number increase by exactly one; it will accept a sequence number that falls within a narrow window or two successive sequence numbers in a much wider window. Rolling code technology is also used on car remote controls and with some internet protocols for secure sites.

The fourth stage of garage door opener systems is similar to third stage, but it is limited to the 315 MHz frequency. The 315 MHz frequency range avoids interference from the land mobile radio system (LMRS) used by the U.S. military.

The following standards are used by units manufactured by Chamberlain (including LiftMaster and Craftsman):

Dates System Color of programming button and LED on unit Color of LED on remote*
1984–1993 8-12 DIP switch on 300-400 MHz white, gray, or yellow button with red LED red
1993–1997 Billion Code on 390 MHz green button with green or red LED green
1997–2005 Security+ (rolling code) on 390 MHz orange or red button with amber LED amber or none
2005–present Security+ (rolling code) on 315 MHz purple button with amber LED none
2011–present Security+ 2.0 (rolling code) on 310, 315, and 390 MHz yellow button with amber LED and yellow antenna wires red or blue

* Does not apply to keyless entry keypads or universal remotes.

Recent Chamberlain garage door openers that have Security+ 2.0 features also use a special serial protocol on wired connections rather than a simple switch closure.[5]

The following standards are used by units manufactured by Overhead Door Corporation and its subsidiary The Genie Company†:

Dates System
1985–1995 9–12 DIP switch on 360, 380, or 390 MHz[6][7]
1995–2005 Intellicode/CodeDodger (rolling code) on 390 MHz
2005–present Intellicode/CodeDodger (rolling code) on 315 MHz
2011–present Intellicode 2/CodeDodger 2 (rolling code) on 315 and 390 MHz

Note: There are no standard color codes for the learn button or LED on units manufactured by Overhead Door or Genie. All accessories made for later versions of Genie Intellicode and Overhead Door CodeDodger are backward compatible with previous generations of Intellicode and CodeDodger.

Cloning garage door opener remotes

[edit]
A typical photo of both the outer case and inner circuit of a garage door opener remote control.

Many garage door opener remote controls use fixed-code encoding which use DIP switches or soldering to do the address pins coding process, and they usually use pt2262/pt2272 or compatible ICs. For these fixed-code garage door opener remotes, one can easily clone the existing remote using a self-learning remote control duplicator (copy remote) which can make a copy of the remote using face-to-face copying.

Additional features

[edit]

Additional features that have been added over the years have included:

  • Automatic courtesy lights that turn on when the door opens (or via motion sensors) and automatically turn off after a preset delay
  • A remote lockout feature, which turns off the radio receiver while one is on vacation or away for an extended time.
  • The availability of accessories has increased, including such features as wireless keypads, key chain remotes, and solenoid-operated deadbolts to lock the door itself.
  • Automatic door closing feature, which after a fixed time by the owner, closes the garage door to prevent theft.

More sophisticated features are also available, such as an integrated carbon monoxide sensor to open the door in case of the garage being flooded with exhaust fumes. Other systems allow door activation over the Internet to allow home owners to open their garage door from their office for deliveries.

Another recent innovation in the garage door opener is a fingerprint-based wireless keypad. This unit attaches to the outside of the garage door on the jamb and allows users to open and close their doors with the press of a finger, rather than creating a personal identification number (PIN). This is especially helpful for families with children who may forget a code and are latchkey kids.

Safety

[edit]
Electric eye for safety

The garage door is generally the largest moving object in a home. An improperly adjusted garage door opener can exert strong and deadly forces and might not reverse the garage door in an emergency. The manufacturer's instructions provide guidance to the user on the proper adjustment and maintenance of the opener.

Garage door openers manufactured and installed in the United States since 1982 are required to provide a quick-release mechanism on the trolley that allows for the garage door to be disconnected from the garage door opener in the event of entrapment.[8] Garage door openers manufactured since 1991 are also required to reverse the garage door if it strikes a solid object.[9][10]

In the United States, the Consumer Product Safety Improvement Act of 1990 required that automatic residential garage door operators manufactured on or after 1 January 1991 conform to the entrapment protection requirements of the 1988 version of ANSI/UL standard 325.[11] A requirement for redundant entrapment-prevention devices was added in 1993; such a system can use an electric eye, a door edge sensor, or any other device that provides equivalent protection by reversing the travel of the closing door if an object is detected in its path.[12][13]

California Senate Bill No. 969

[edit]

In California, Senate Bill No. 969 requires that any automatic residential garage door opener that is manufactured for sale, sold, offered for sale, or installed in a residence to have a battery backup function that is designed to operate when activated because of an electrical outage.[14] The bill went into effect on July 1, 2019. Under the bill, any automatic garage door opener that is in violation is subject to a civil penalty of $1000.

The bill was passed by Gov. Jerry Brown on Sept. 21, 2018, in response to the 2017 California Wildfires in which at least 5 individuals lost their lives because they could not open their garage door when the power went out.[15]

The Door and Access Systems Manufacturers Association International opposed the bill arguing that garage door openers with backup batteries require regular maintenance and that the bill should be amended to make this clear. In addition, they said that "garage door openers with backup batteries are not designed to serve as life safety devices, and should not be relied upon to prove a means of egress from a garage during an electrical outage."[16]

The bill passed, despite most garage doors having a release pull cord.

References

[edit]
  1. ^ Robert J Girod (2014). "Garage Door Openers - High-tech Burglary". Advanced Criminal Investigations and Intelligence Operations: Tradecraft Methods, Practices, Tactics, and Techniques. Taylor and Francis. p. 90. ISBN 9781482230741.
  2. ^ "Aids To Modern Living - Garage Doors". Popular Science: 137. December 1946.
  3. ^ Castro, Diane. "The Complete Garage Door System". Regency Conference Center. Retrieved 10 March 2020.
  4. ^ "Widely Separated Inventors Invent Garage Door Openers By Radio Impulses". Popular Science: 32. February 1931.
  5. ^ "Will my older accessories work with the new line of Security+ 2.0 garage door openers?". alldaygaragerepair.com. Retrieved 2017-06-23.
  6. ^ Willmes, Dave. "My Overhead Door Opener Doesn't Work with this Universal Remote". www.overheaddooronline.com. Retrieved 20 October 2016.
  7. ^ "FCC ID BSH8YN106546 by Overhead Door Corporation". FCCID.io. Retrieved 20 October 2016.
  8. ^ "Falling Garage Doors — A Crushing Concern". Garage Door Child Safety.
  9. ^ "Non Reversing Garage Door Openers a Hazard" (PDF). U.S. Consumer Product Safety Commission.
  10. ^ "Garage Door System Safety Guidelines". Door & Access Systems Manufacturers Association International. Archived from the original on 2008-12-23.
  11. ^ Garage Door Operators • CPSC
  12. ^ Non-Reversing Automatic Garage Door Openers Are a Hazard • CPSC
  13. ^ 16CFR1211
  14. ^ "Bill Text - SB-969 Automatic garage door openers: backup batteries". leginfo.legislature.ca.gov. California Legislative Information. Retrieved 6 September 2019.
  15. ^ "New California Law Could Cost You $1000 in Fines". Clark's Garage Door. 4 September 2019. Retrieved 6 September 2019.
  16. ^ "California Mandates Battery Backup With All GDOS - Experts Cite Problems With The Legislation" (PDF). dasma.com. DASMA. Retrieved 6 September 2019.
[edit]
  • Official FCC notification on garage opener frequencies (PDF)
  • Garage Door Opener Safety Tips (Washington Post)
  • Safety Commission Rules For Automatic Garage Door Openers - U.S. Consumer Product Safety Commission. CPSC, 1992
Photo
Photo
Photo
Photo
Photo

Driving Directions in Will County


Driving Directions From Honorable Edward A Burmila Jr to Overhead Door Company of Joliet
Driving Directions From First American Bank to Overhead Door Company of Joliet
Driving Directions From Honorable Robert P Livas to Overhead Door Company of Joliet
Driving Directions From Route 66 Park to Overhead Door Company of Joliet
Driving Directions From Joliet Iron Works Park to Overhead Door Company of Joliet
Driving Directions From Lake Katherine Nature Center and Botanic Gardens to Overhead Door Company of Joliet
Driving Directions From Joliet Iron Works Park to Overhead Door Company of Joliet
Driving Directions From Gemini Giant to Overhead Door Company of Joliet
Driving Directions From Lockport Prairie Nature Preserve to Overhead Door Company of Joliet
Driving Directions From Knoch Knolls Nature Center to Overhead Door Company of Joliet

Reviews for Overhead Door Company of Joliet


Overhead Door Company of Joliet

Kelley Jansa

(5)

We used Middleton Door to upgrade our garage door. We had three different companies come out to quote the job and across the board Middleton was better. They were professional, had plenty of different options and priced appropriately. The door we ordered came with a small dent and they handled getting a new panel ordered and reinstalled very quickly.

Overhead Door Company of Joliet

Andrea Nitsche

(4)

Scheduling was easy, job was done quickly. Little disappointed that they gave me a quote over email (which they confirmed was for labor and materials), but when they finished it was just over $30 more. Not a huge deal, but when I asked why, I was told they gave me an approx cost and it depends on what is needed. I get that in general, however, they installed the door and I gave them my address and pics of the existing prior to getting a quote. I feel like they could have been more upfront with pricing. And just a heads up, it was pricey... Had them change the weather stripping, from ringing my doorbell to pulling out my driveway when done was literally 20 mins, cost was just over $260 😬

Overhead Door Company of Joliet

Jim Chuporak

(5)

Received a notice the morning of telling me when to expect the men to come and put the door in. he was on time, answered all my questions, worked diligently in the cold. And did an absolutely awesome job. Everything was cleaned up, hauled away from the old door. I am extremely happy with the service I received from the first phone call I made through having the door put in. My wife and I are very, very happy with the door.

View GBP

Frequently Asked Questions

Look for visible signs such as gaps between the hinge and the door or frame, rust or corrosion around the hinge screws, or unusual noises like squeaking during operation. Regularly check for any movement when you manually wiggle the door.
You will typically need a screwdriver (either flathead or Phillips, depending on your hinges), a socket wrench for nuts and bolts, and possibly lubricating oil to ensure smooth operation after tightening.
Regular maintenance is key; this includes routinely checking and tightening screws, applying lubrication to prevent rust, ensuring proper alignment of the door, and replacing worn-out parts promptly.